Message
Description
I/O CARD READY, or READY: The HP Jetdirect print server has successfully connected
to the network and is awaiting data.
I/O CARD INITIALIZING, or INITIALIZING: The HP Jetdirect print server is initializing
the network protocols. For more information, see the status line for each protocol on the
configuration page.
I/O CARD NOT READY, or ERROR: There is a problem with the print server or its
configuration.
An error code and message is displayed if the print server is not ready. For more
information, see
Table 8-12 Error Messages
.
MODEL NUMBER:
The product number of the HP Jetdirect print server (for example, J7982E)
HARDWARE ADDRESS:
The 12-digit hexadecimal network hardware (MAC) address of the HP Jetdirect print
server installed in the printer or device. This address is assigned by the manufacturer.
FIRMWARE VERSION:
The firmware revision number of the HP Jetdirect print server currently installed in the
printer.
LAA
The Locally Administered Address (LAA) identifies the user-specified LAN hardware
address of a print server, which may be required by some network adiministrators. The
default address is the print server's factory-default LAN hardware address.
PORT CONFIG:
Identifies the link configuration of the RJ-45 port on the HP Jetdirect wired Ethernet print
server:
10BASE-T HALF: 10 Mbps, half-duplex
10BASE-T FULL: 10 Mbps, full-duplex
100TX HALF: 100Mbps, half-duplex
100TX-FULL: 100Mbps, full-duplex
1000T-FULL: 1000 Mbps, full-duplex
UNKNOWN: The print server is in an initialization state.
DISCONNECTED: A network connection has not been detected. Check network cables.
AUTO NEGOTIATION
Identifies whether IEEE 802.3u Auto-negotiation on the HP Jetdirect 10/100/1000T port
is enabled (ON) or disabled (OFF).
ON (default): The HP Jetdirect print server will attempt to automatically configure itself
onto the network at the proper speed (10, 100, 1000 Mbps) and mode (half or full
duplex). Auto-negotiation is enabled after a cold reset.
OFF: You must manually configure the speed and mode using the Jetdirect menu from
the printer's control panel. If Auto-negotiation is off, the settings must match those of
the network for proper operation.
MANUFACTURING ID:
The manufacturing identification code for use by HP online support personnel.
S/N:
The serial number of the HP Jetdirect print server.
DATE MANUFACTURED:
Identifies the date of manufacture of the HP Jetdirect print server.
Security Settings
Information in this section of the Jetdirect configuration page is described in
Table 8-3 Security Settings
.
Table 8-2
HP Jetdirect Configuration (continued)
120
Chapter 8 HP Jetdirect Configuration Pages
ENWW
Содержание Jetdirect J7974E
