![background image](http://html.mh-extra.com/html/hp/jetdirect-j7974e/jetdirect-j7974e_administrators-manual_163704058.webp)
3
: The default LPD raw queue
4
: The default LPD text queue
5
: The default LPD auto queue
6
: The default LPD binps (binary PostScript) queue
7
through
12
: If user-specified LPD queues are defined, corresponds to user-specified LPD
queues 5 through 10.
The default selection will depend on the printer, typically port 9100 printing or LPD binps.
ttl-slp
Specifies the IP multicast “Time To Live” (TTL) setting for Service Location Protocol (SLP)
packets. The default value is 4 hops (the number of routers from the local network). The
range is 1–15. When set to a -1, multicast capability is disabled.
ipv4-multicast
Enables or disables the receipt and transmission of IP version 4 multicast packets by the
print server.
0
disables,
1
(default) enables.
NOTE
If this parameter is disabled, other protocols that use multicast protocols,
such as Bonjour and SLP, may also be disabled without notification.
idle-timeout
An integer (1to 3600) that specifies the number of seconds an idle print data connection
is allowed to remain open. For example,
idle-timeout 120
assigns 120 seconds as the desired idle timeout value.
The default is 270 seconds. If set to 0, the connection will not terminate and other hosts
will not be able to make a connection.
user-timeout
An integer (1to 3600) that specifies the number of seconds that your Telnet or FTP session
can be idle before it will be automatically disconnected. The default is 900 seconds. 0
disables the timeout.
CAUTION
Small values, such as 1–5, may effectively disable the use of Telnet.
A Telnet session may terminate before any changes can be made.
cold-reset
1
: Sets TCP/IP factory default settings. After a cold reset, power cycle the print server.
Parameters for other subsystems, such as IPX/SPX or AppleTalk, are not affected.
0
: Normal operation, and reset is disabled.
ews-config
Enables or disables the print server's embedded Web server.
0
disables,
1
(default)
enables.
For more information, see
HP Jetdirect Embedded Web Server (V.34.xx)
.
web-refresh
Specifies the time interval (1–99999 seconds) for embedded Web server diagnostic page
updates. If set to 0, the refresh rate is disabled.
tcp-mss
Specifies the maximum segment size (MSS) that the HP Jetdirect print server will advertise
for use when communicating with local subnets (Ethernet MSS=1460 bytes or more) or
remote subnets (MSS=536 bytes):
0
: (default) All networks are assumed to be local (Ethernet MSS=1460 bytes or more).
1
: Use MSS=1460 bytes (or more) for subnets, and MSS=536 bytes for remote networks.
2
: All networks are assumed to be remote (MSS=536 bytes), except the local subnet.
Table 3-3
Telnet Commands and Parameters (continued)
48
Chapter 3 TCP/IP Configuration
ENWW
Содержание Jetdirect J7974E
