![background image](http://html.mh-extra.com/html/hp/jetdirect-j7974e/jetdirect-j7974e_administrators-manual_163704082.webp)
Item
Description
AUTO_IP
: sets a link-local IP address 169.254.x.x.
The initial setting is determined by the IP address obtained when first powered on.
Send DHCP requests
(IPv4 only) A checkbox is used to specify whether DHCP requests will be periodically
transmitted when a legacy default IP address 192.0.0.192 or link-local IP address
169.254.x.x has been automatically assigned.
Clear the checkbox to disable DHCP requests.
Check the checkbox (default) to enable DHCP requests.
Use Stateless DHCPv4 When
Manually Configured
(IPv4 only) A checkbox is used to allow additional IPv4 parameters to be automatically
configured from a DHCPv4 server even when the print server is statically configured
(such as a manually configure IP address, subnet mask and default gateway).
Clear the checkbox to disable stateless DHCPv4 configuration.
Check the checkbox (default) to enable stateless DHCPv4 configuration.
TTL/SLP
(IPv4 only) Specifies the IP multicast Time To Live (TTL) discovery setting for Service
Location Protocol (SLP) packets. The default value is 4 hops (the number of routers
from the local network). The range is 1–15. If set to
−
1, multicast capability is disabled.
For print servers configured for Auto IP (link-local) addresses, this field will be ignored.
TTL on outbound packets will always be set to 255 and limited to the link-local network.
Syslog Server
(IPv4 only) Specifies the IP address of a host computer that is configured to receive
syslog messages from the HP Jetdirect print server. If a Syslog Server is not specified,
syslog messages are disabled.
Syslog Maximum Messages
(IPv4 only) Specifies the maximum number of syslog messages that can be sent by the
HP Jetdirect print server on a per-minute basis. This setting allows administrators to
control the log file size. The default is 10 per minute. If set to zero, no maximum number
is defined.
Syslog Priority
(IPv4 only) Controls the filtering of syslog messages that are sent to the syslog server.
The filter range is 0 to 8, with 0 being the most specific and 8 being the most general.
Only messages that are lower than the filter level specified (that is, higher in priority)
are reported. The default value is 8 which reports all syslog messages. A value of zero
effectively disables syslog reporting.
Network Settings
The
Network Settings
pages allow you to set or change configuration parameters for
IPX/SPX
,
AppleTalk
,
DLC/LLC
, and
SNMP
protocols. To assign a parameter setting, enter the desired value and
click
Apply
.
IPX/SPX
The
IPX/SPX
tab allows you to configure IPX/SPX (Internet Packet Exchange/Sequenced Packet
Exchange) parameters on the HP Jetdirect print server for operation on a Novell NetWare or IPX/SPX-
compatible network (such as a Microsoft network). See
Table 4-9 IPX/SPX Settings
for a description of
items on this page.
CAUTION
If you are using direct-mode printing over IPX/SPX on a Microsoft network,
do not
disable IPX/SPX.
Table 4-8
TCP/IP Advanced tab (continued)
72
Chapter 4 HP Jetdirect Embedded Web Server (V.34.xx)
ENWW
Содержание Jetdirect J7974E
