![background image](http://html.mh-extra.com/html/hp/jetdirect-j7974e/jetdirect-j7974e_administrators-manual_163704087.webp)
Item
Description
HP XML Services
Enable or disable access by HP Web service applications to XML-based data on the HP
Jetdirect print server.
Link settings
(For wired 10/100/1000T Ethernet) Sets the print server's link speed (10, 100, 1000 Mbps)
and communication mode (Full- or Half-Duplex). The available link-speed selections
depend on the print server model. The selections that may be displayed are listed below.
CAUTION
If you change the link setting, network communications with the print
server and network device may be lost.
●
AUTO
(default): The print server uses auto-negotiation to configure itself with the
highest link speed and communication mode allowed. If auto-negotiation fails, either
100TX HALF or 10TX HALF is set depending on the detected link speed of the hub/
switch port. (A 1000T half-duplex selection is not supported.)
●
10T-Full
: 10 Mbps, Full-duplex operation.
●
10T-Half
: 10 Mbps, half-duplex operation.
●
100TX-Full
: 100 Mbps, full-duplex operation.
●
100TX-Half
: 100 Mbps, half-duplex operation.
●
100TX-AUTO
: Limits auto-negotiation to a maximum link speed of 100 Mbps.
●
1000T FULL
: 1000 Mbps, full-duplex operation.
Locally Administered Address
Specifies a locally administered address (LAA) that replaces the factory-assigned LAN
Hardware (MAC) address. If LAA is used, a user-specified string of exactly 12 hexadecimal
digits must be entered.
For Ethernet print servers, the LAA address must start with hexadecimal X2, X6, XA, or
XE, where X is any hexadecimal digit 0 through F.
The default address is the factory assigned address.
Syslog Facility
Specify the encoded source facility of a message (for example, to identify the source of
selected messages during troubleshooting). By default, the HP Jetdirect print server uses
LPR as the source facility code, but local user values of local0 through local7 can be used
to isolate individual or groups of print servers.
HTTP Idle Timeout
Specifies the length of time after which an idle HTTP connection will be closed. The HTTP
Idle Timeout applies to the time after an HTTP request or response has completed. The
valid range is 5 to 60 seconds. The default value is 15.
If zero (0) is specified, this parameter is disabled, and the TCP/IP idle timeout value is
used.
Dynamic Raw Port Setting
Allows additional ports to be specified for printing to TCP port 9100. Valid ports are 3000
to 9000, which are application-dependent.
Disable listening on these ports
NOTE
While supported in this release, this item may be superseded or
overridden by the
IPsec/Firewall
policy configuration.
For security purposes, two fields allow you to disable services on the printer that use the
network. In each field, you must specify the port numbers that are used for network
communications with those services. Up to five ports may be specified in each field (for
example, [5, 10, 40, 20, 50]). The valid range for port numbers is 1 through 65535.
Streams
: In this field, enter port numbers of services that pass data streams. Data streams
use Transport Control Protocol (TCP) to guarantee data delivery.
Table 4-12
Miscellaneous Settings (continued)
ENWW
Networking Tab
77
Содержание Jetdirect J7974E
