HP Jetdirect J7974E Скачать руководство пользователя

Страница: 169 / 186

Menu Item

Submenu Options

Additional Options

Description of settings

MANUAL
SETTINGS

(Available only if CONFIG METHOD is set to MANUAL)
Configure parameters directly from the printer control
panel:

●

IP ADDRESS n.n.n.n: The unique IP address of the
printer, where n is a value from 0 to 255.

●

SUBNET MASK m.m.m.m: The subnet mask for the
printer, where m is a value from 0 to 255.

●

SYSLOG SERVER n.n.n.n: The IP address of the
syslog server used to receive and log syslog
messages.

●

DEFAULT GATEWAY n.n.n.n: The IP address of
the gateway or router used for communications with
other networks.

●

IDLE TIMEOUT: The time period, in seconds, after
which an idle TCP print data connection is closed
(default is 270 seconds, 0 disables the timeout).

DEFAULT IP

Specify the IP address to default to when the print server
is unable to obtain an IP address from the network during
a forced TCP/IP reconfiguration (for example, when
manually configured to use BootP or DHCP).

●

AUTO IP: A link-local IP address 169.254.x.x will be
set.

●

LEGACY: The address 192.0.0.192 will be set,
consistent with older Jetdirect products.

PRIMARY DNS

Specify the IP address (n.n.n.n) of a Primary DNS
Server.

SECONDARY DNS

Specify the IP address (n.n.n.n) of a Secondary Domain
Name System (DNS) Server.

IPV6 SETTINGS

ENABLE

Use this item to enable or disable IPv6 operation on the
print server.

ON: IPv6 will be enabled.

OFF: IPv6 will be disabled.

ADDRESS

Use this item to manually configure an IPv6 address.

MANUAL SETTINGS: Use the MANUAL SETTINGS
menu (see the additional options under IPV6
SETTINGS) to enable and manually configure a TCP/
IPv6 address.

LINK-LOCAL: Use this item to display the IPv6 link-local
address configured on the print server.

DHCPV6: If available, use this item to display stateful
IPv6 addresses controlled by a DHCPv6 server.

ROUTER SPECIFIED: If available, use this item to
display stateless addresses associated with a router.

DHCPV6 POLICY

ROUTER SPECIFIED: The stateful auto-configuration
method to be used by the print server is determined by

Table C-1

HP Jetdirect Control Panel Menu (continued)

ENWW

Parameter Descriptions

159

Содержание Jetdirect J7974E



























































































































































































Результаты поиска

Содержание Jetdirect J7974E

Отзывы:

Похожие инструкции для Jetdirect J7974E

Бренды по названию

Популярные бренды

HP Jetdirect J7974E, Руководство администратора

Результаты поиска

Содержание Jetdirect J7974E

Отзывы:

Похожие инструкции для Jetdirect J7974E

Бренды по названию

Популярные бренды