auth-trap
Configures the print server to send (on) or not send (off) SNMP authentication traps.
Authentication traps indicate that an SNMP request was received, but the community name
check failed. 0 is off, 1 (default) is on.
trap-dest
Enters a host IP address into the HP Jetdirect print server's SNMP trap destination list.
The command format is:
trap-dest:
ip-address [community name] [port number]
The default community name is ‘public’; the default SNMP port number is ‘162’. The port
number cannot be specified without a community name.
To delete the table, use ‘trap-dest: 0’.
If the list is empty, the print server does not send SNMP traps. The list may contain up to
six entries. The default SNMP Trap Destination List is empty. To receive SNMP traps, the
systems listed on the SNMP trap destination list must have a trap daemon to listen to those
traps.
IPX/SPX
ipx-config
Enables or disables IPX/SPX protocol operation on the print server. 0 disables, 1 (default)
enables. For example,
ipx-config 0
will disable IPX/SPX operation.
ipx-unitname
(Print Server Name) A user-assigned alphanumeric name assigned to the print server (31
characters maximum). By default, the name will be NPIxxxxxx, where xxxxxx are the last
six digits of the LAN hardware address.
Address
(Read-only parameter) Identifies the IPX network and node numbers detected on the
network, in the form NNNNNNNN:hhhhhhhh (hexadecimal), where NNNNNNNN is the
network number and hhhhhhhh is the LAN hardware address of the print server.
ipx-frametype
Specifies the IPX frame type settings available for your print server model:
AUTO
(default),
EN_SNAP, EN_8022, EN_8023, EN_II
. For more information, see
HP Jetdirect
Configuration Pages
.
ipx-sapinterval
Specifies the time interval (1 to 3600 seconds) that the HP Jetdirect print server waits
between Service Advertising Protocol (SAP) broadcasts on the network. The default is 60
seconds. 0 disables SAP broadcasts.
ipx-mode
(Read-only parameter) Specifies the NetWare mode configured on the print server, either
RPRINTER or QSERVER mode.
ipx-nds-tree
An alphanumeric string, up to 31 characters, that specifies the NDS tree name for the print
server.
ipx-nds-context
An alphanumeric string, up to 256 characters, that specifies the NDS context for the HP
Jetdirect print server.
ipx-job-poll
Specifies the time interval (1 to 255 seconds) that the HP Jetdirect print server will wait to
check for print jobs in a print queue. The default is 2 seconds.
pjl-banner
(ipx-banner)
Enables or disables printing an IPX banner page through Printer Job Language (PJL).
0
disables banner pages.
1
(default) enables banner pages.
pjl-eoj
(ipx-eoj)
Enables or disables IPX end-of-job notification through PJL.
0
disables,
1
(default) enables.
pjl-toner-low
(ipx-toner-low)
Enables or disables IPX toner-low notification through PJL.
0
disables,
1
(default) enables.
AppleTalk
Table 3-3
Telnet Commands and Parameters (continued)
ENWW
IPv4 Configuration
51
Содержание Jetdirect J7974E
