![background image](http://html.mh-extra.com/html/hp/jetdirect-j7974e/jetdirect-j7974e_administrators-manual_163704033.webp)
Default IPv4 Behavior
When powered on, a factory-default print server connected to a network through a cable (wired) will
systematically use BOOTP, DHCP, and RARP to retrieve its IPv4 settings. Up to two minutes are used.
If configuration is not successful, a default IPv4 address will be assigned as described previously.
Configuration tools that require a specific default IP address on the print server for initial communication
may not work without modification. For the default IP address settings actually configured on the print
server, see the Jetdirect configuration page.
TCP/IP Configuration Tools
When a network connection has been established, an HP Jetdirect print server can be configured with
valid TCP/IP parameters for your network in the following ways:
●
Using Software
. You can use installation, setup, and management software running on supported
systems. For more information see
HP Software Solutions Summary
.
●
BOOTP/TFTP
. You can download the data from a network-based server using BOOTP (Bootstrap
Protocol) and TFTP (Trivial File Transfer Protocol) each time the printer is turned on. For more
information, see “
Using BOOTP/TFTP (IPv4)
”.
The BOOTP daemon, bootpd, must be running on a BOOTP server that is accessible by the printer.
●
DHCP/TFTP
. You can use Dynamic Host Configuration Protocol (DHCP) and TFTP (Trivial File
Transfer Protocol) each time the printer is turned on. These protocols are supported on HP-UX,
Solaris, Linux, Windows 2000/Server 2003, NetWare and Mac OS systems. (Refer to your network
operating system manuals to verify that your server operating system supports DHCP.) For more
information, see “
Using DHCP (IPv4)
”.
NOTE
Linux and UNIX systems: For more information, see the bootpd “
man
” page.
On HP-UX systems, a sample DHCP configuration file (dhcptab) may be located in the
/
etc
directory.
Since HP-UX presently does not provide Dynamic Domain Name Services (DDNS) for its
DHCP implementations, HP recommends that you set all print server lease durations to
infinite
. This ensures that print server IP addresses remain static until such time as Dynamic
Domain Name Services are provided.
●
RARP
. A network-based server can use RARP (Reverse Address Resolution Protocol) to answer
the print server's RARP request and supplying the print server with the IP address. The RARP
method only allows you to configure the IP address. For more information, see “
Using RARP
(IPv4)
”.
●
arp and ping commands
. (For print servers configure with Legacy default IP address 192.0.0.192
only) You can use the
arp
and
ping
commands from your system. For more information, see
“
Using the arp and ping Commands (IPv4)
”.
●
Telnet
. You can set configuration parameters using Telnet. In order to set configuration
parameters, set up a Telnet connection from your system to the HP Jetdirect print server using the
default IP address. Once configured, the print server saves the configuration when powered off/
on. For more information, see “
Using Telnet (IPv4)
”.
ENWW
IPv4 Configuration
23
Содержание Jetdirect J7974E
