HP Jetdirect J7974E Скачать руководство пользователя страница 134 | Manualshive

Страница: 134 / 186

background image

Message

Description

Not Specified: Indicates that a WINS server's IP address has not been configured on
the print server.

IDLE TIMEOUT:

The timeout value expressed in seconds after which the print server closes an idle TCP
print data connection. Acceptable values are integers between 0 and 3600. A value of
zero turns off the timeout mechanism. The default value is 270 seconds.

IPv4 Section

The following table includes items displayed under the IPv4 section of the configuration page.

Table 8-6

IPv4 Section

Message

Description

STATUS:

Current TCP/IPv4 status.

READY: Indicates the HP Jetdirect print server is awaiting data over TCP/IP.

DISABLED: Indicates that TCP/IP was manually disabled.

INITIALIZING: Indicates that the print server is searching for the BOOTP server, or
trying to get the configuration file through TFTP. An additional status message may also
be displayed.

An error code and message is displayed if the print server is not ready. For more
information, see

Table 8-12 Error Messages

.

IP ADDRESS:

The Internet Protocol version 4 (IPv4) address assigned to the HP Jetdirect print server.
This is a required entry for operation of the print server on a TCP/IP network. During
initialization, a temporary value 0.0.0.0 is displayed. After two minutes, a default IP
address 169.254/16 or 192.0.0.192 is assigned.

Not Specified: Indicates that an IP address is not assigned or the value is zero.

SUBNET MASK:

The IPv4 subnet mask configured on the HP Jetdirect print server. During initialization,
a temporary value 0.0.0.0 is displayed. Depending on configuration parameters, the
print server may automatically assign a usable default value.

Not Specified: Indicates that a subnet mask is not configured.

DEFAULT GATEWAY:

The IPv4 address of the gateway used when sending packets off the local network. Only
one default gateway may be configured. During initialization, a temporary value 0.0.0.0
is displayed. If not provided, the IP address of the Jetdirect print server is used.

Not Specified: Indicates that a default gateway is not configured.

CONFIG BY:

Identifies how the HP Jetdirect print server obtained its IPv4 configuration:

BOOTP: Automatic configuration through a BOOTP server.

BOOTP/TFTP: Automaticautomatic configuration through a BOOTP server and TFTP
configuration file.

DHCP: Automatic configuration through a DHCP server

DHCP/TFTP: Automatic configuration through a DHCP server and TFTP configuration
file.

RARP: Automatic configuration through the Reverse Address Resolution Protocol.

Table 8-5

TCP/IP Configuration Information (continued)

124

Chapter 8 HP Jetdirect Configuration Pages

ENWW

«
...
132
133
134
135
136
...
»

Содержание Jetdirect J7974E



























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Jetdirect J7974E

iPF650 - imagePROGRAF Color Inkjet Printer

Бренд: Canon Страницы: 40

iP90 - PIXMA Color Inkjet Printer

Бренд: Canon Страницы: 2

iPF650 - imagePROGRAF Color Inkjet Printer

Бренд: Canon Страницы: 16

iP100 - PIXMA Color Inkjet Printer

Бренд: Canon Страницы: 2

imageRUNNER ADVANCE C5560

Бренд: Canon Страницы: 67

iPF710 - imagePROGRAF Color Inkjet Printer

Бренд: Canon Страницы: 2

Бренд: JCM Страницы: 22

Бренд: Nanoptix Страницы: 25

Бренд: Nanoptix Страницы: 4

Бренд: Xerox Страницы: 93

Бренд: Xerox Страницы: 36

Бренд: Xerox Страницы: 136

3250D - Phaser B/W Laser Printer

Бренд: Xerox Страницы: 6

7760DN - Phaser Color Laser Printer

Бренд: Xerox Страницы: 6

Бренд: Canon Страницы: 20

PIXMA TS9100 Series

Бренд: Canon Страницы: 100

Бренд: Canon Страницы: 100

Бренд: Canon Страницы: 105

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды