Honda CB HORNET 160R 2015 Скачать руководство пользователя страница 249

Страница: 249 / 336

14-5

BRAKE SYSTEM

If a brake bleeder is not available then use the following

steps:

Fill the reservoi

r with DOT 3 or DOT 4 brake fluid from a

sealed container.

Connect a bleed hose to the front brake caliper bleed valve.

STEP 1:

Pressurize the system with the brake lever until

lever resistance is felt.

STEP 2:

Squeeze the brake lever, open the bleed valve ¼ turn

and then close the valve.

NOTE:

• Do not release the lever until the bleed valve has been

closed.

•

If an automatic refill system is not used, add brake fluid

when the fluid level in the reservoir is low.

•

Check the fluid level often while bleeding the brakes to

prevent air from being pumped into the system.

• If air is entering the bleeder from around the bleed valve

threads, seal the threads with teflon tape.

Repeat

steps 1. and 2

. until air bubbles do not appear in

the bleed hose.

After bleeding the air completely, tighten the brake caliper

bleed valve to the specified torque.

TORQUE: 5.4 N·m (0.6 kgf·m, 4.0 lbf·ft)

BLEED

HOSE

BLEED

HOSE

NON CBS

CBS

BLEED VALVE

Do not mix

different types of

fluid. These are

not compatible

BLEED HOSE

BLEED VALVE

COMBI BRAKE SYSTEM (CBS)

Combine brake system (page 14-3) consist of two individual
hydraulic circuit, the front brake line and CBS line.

• Front brake line - Bleeding procedure same as front

brake non CBS

• Rear brake line and CBS brake line - Bleeding

procedure follow the below process

Note: Always bleed the rear brake line first before bleeding

the CBS brake line.

REAR BRAKE

If a brake bleeder/automatic refill system is available

then use the following steps:

Connect the automatic refill system to the reservoir, follow

the manufacturer’s operation instruction.

Connect the commercially available brake bleeder to the
Rear bleed valve.

Perform the bleeding procedure until the system is

completely flushed/ bleed.

After bleeding the air completely, tighten the brake caliper

bleed valve to the specified torque.

TORQUE: 5.4 N.m (0.6 kgf.m, 4.0 lbf.ft)

Содержание CB HORNET 160R 2015

















































































































































































































































































































































Результаты поиска

Содержание CB HORNET 160R 2015

Отзывы:

Похожие инструкции для CB HORNET 160R 2015

Бренды по названию

Популярные бренды

Honda CB HORNET 160R 2015, Руководство по ремонту

Результаты поиска

Содержание CB HORNET 160R 2015

Отзывы:

Похожие инструкции для CB HORNET 160R 2015

Бренды по названию

Популярные бренды