Honda CB HORNET 160R 2015 Скачать руководство пользователя страница 143

Страница: 143 / 336

9-5

CLUTCH/GEARSHIFT LINKAGE

DOWEL PINS

GASKET

Install the right crankcase cover, clutch cable holder and
right crankcase cover bolts.

Tighten the right crankcase cover bolts in a crisscross
pattern in 2 or 3 steps.

TORQUE: 9 N·m (0.9 kgf·m, 6.6 lbf·ft)

Install the kick start stopper and tighten the bolts/nuts
(2 nos.).

Install the clutch lifter piece into the clutch lifter arm groove
by aligning the groove with the lifter piece hole.

INSTALLATION

Clean off any gasket material from the mating surfaces of
the right crankcase and cover.

Install the dowel pins and new gasket.

Connect the clutch cable to the clutch lifter arm.

Adjust the clutch lever free play (page 3-22).

Install the following:

– Kick starter pedal (page 6-6)

Fill the crankcase with the recommended engine oil
(page 3-10).

Be careful not

to damage the

mating surfaces.

RETURN SPRING

LIFTER PIECE

LIFTER ARM

CLUTCH CABLE

LOCK NUT

ADJUSTING NUT

BOLTS

HOLDER

KICK
START
STOPPER

COVER

Содержание CB HORNET 160R 2015

















































































































































































































































































































































Результаты поиска

Содержание CB HORNET 160R 2015

Отзывы:

Похожие инструкции для CB HORNET 160R 2015

Бренды по названию

Популярные бренды

Honda CB HORNET 160R 2015, Руководство по ремонту

Результаты поиска

Содержание CB HORNET 160R 2015

Отзывы:

Похожие инструкции для CB HORNET 160R 2015

Бренды по названию

Популярные бренды