Honda CB HORNET 160R 2015 Скачать руководство пользователя страница 55

Страница: 55 / 336

3-17

MAINTENANCE

Use any one of the following methods for lubricating drive

chain:

•  SAE 80 or 90 gear oil
•  Honda recommended chain maintenance spray
•  Molten grease in greaselator

Saturate each chain link joint so that the lubricant

penetrates between the link plates, pins, bushings, and

rollers.

Wipe off the excess gear oil or grease.

If the drive chain becomes extremely dirty, it should be

removed and cleaned prior to lubrication.
Remove the drive chain case (page 3-16).

Carefully remove the retaining clip with pliers.

Remove the master link, link plate and drive chain.

Clean the chain with non-flammable or high flashpoint

solvent and wipe it dry.
Be sure the chain has dried completely before lubricating.
Lubricate the drive chain.

Wipe off the excess gear oil or grease.

INSPECTION

DRIVE CHAIN

Inspect the drive chain for possible damage or wear.
Replace any chain that has damaged rollers, loose fitting

links, or otherwise appears unserviceable.
Measure the drive chain length with the chain held so that

all links are straight.

DRIVE CHAIN SPEC. :
NUMBER OF LINKS : 132
STANDARD LENGTH: 428 mm (16.85 in)
SERVICE LIMIT:

511 mm (20.11 in)

RETAINING CLIP

LINK PLATE

(N+1)PINS/(N) LINKS

MASTER LINK

NON-FLAMMABLE

OR HIGH FLASH

POINT SOLVENT

GEAR OIL/

GREASE

CLEANING

WIPE AND

DRYING

LUBRICATE

SOFT BRUSH

Содержание CB HORNET 160R 2015

















































































































































































































































































































































Результаты поиска

Содержание CB HORNET 160R 2015

Отзывы:

Похожие инструкции для CB HORNET 160R 2015

Бренды по названию

Популярные бренды

Honda CB HORNET 160R 2015, Руководство по ремонту

Результаты поиска

Содержание CB HORNET 160R 2015

Отзывы:

Похожие инструкции для CB HORNET 160R 2015

Бренды по названию

Популярные бренды