Honda CB HORNET 160R 2015 Скачать руководство пользователя страница 135

Страница: 135 / 336

8-7

CYLINDER/PISTON

Clean any gasket material from the cylinder mating surface
of the crankcase.

Place a shop towel over the crankcase opening to prevent
piston pin clips from falling into the crankcase.

Apply molybdenum oil solution to the piston pin outer
surface.

Install the piston with its “IN” mark facing the intake side.

Install the piston pin.

TOOL:

Slider base piston

070SRTKSP008

Install the new piston pin clips:

• Always use new piston pin clips. Reinstalling used

piston pin clips may lead to serious engine damage.

• Set the piston pin clip in the groove properly.

• Do not align the clip’s end gap with the piston cutout.

CYLINDER INSTALLATION

Install the dowel pins and new gasket.

When cleaning

the cylinder

mating surface,

place a shop

towel over the

cylinder opening

to prevent dust

or dirt enter the

engine.

Do not reuse the

gasket, replace

with a new one.

MATING SURFACE

PISTON PIN

“IN MARK”

PISTON

PISTON PIN CLIP

DOWEL PIN

GASKET

Содержание CB HORNET 160R 2015

















































































































































































































































































































































Результаты поиска

Содержание CB HORNET 160R 2015

Отзывы:

Похожие инструкции для CB HORNET 160R 2015

Бренды по названию

Популярные бренды

Honda CB HORNET 160R 2015, Руководство по ремонту

Результаты поиска

Содержание CB HORNET 160R 2015

Отзывы:

Похожие инструкции для CB HORNET 160R 2015

Бренды по названию

Популярные бренды