Honda CB HORNET 160R 2015 Скачать руководство пользователя страница 258

Страница: 258 / 336

14-14

BRAKE SYSTEM

FRONT BRAKE CALIPER

CBS FRONT BRAKE
REMOVAL

Drain the brake fluid from the hydraulic system (page 14-3).

Remove the brake pads (page 14-7).

Remove the brake hose by removing the oil bolt and
sealing washer.

Remove the brake caliper mounting bolts and brake caliper.

DISASSEMBLY

Remove the caliper bracket from the caliper body.

Remove the pad spring and bracket pin boot from the
caliper body.

Remove the pad retainer and caliper pin boot from the
caliper bracket.

If the bracket pin boot is hard or deteriorated, replace it
with a new one.

BOLTS

SEALING WASHERS

OIL BOLT

CALIPER BRACKET

PAD SPRING

PAD RETAINER

CALIPER

PIN BOOT

BRACKET
PIN BOOT

CALIPER

BODY

Place a shop towel over the caliper pistons.

Position the caliper body with the piston down, and apply

small squirts of air pressure to the fluid inlet to remove the

caliper pistons.

Push the dust seals and piston seals in, and lift them out.

Clean the seal grooves, caliper piston sliding surfaces and

caliper pistons with clean brake fluid.

Do not use high

pressure air or

bring the

nozzle too close

to the inlet.

Be careful not to

damage the

piston

sliding surface.

PISTON SEAL

DUST SEAL

Содержание CB HORNET 160R 2015

















































































































































































































































































































































Результаты поиска

Содержание CB HORNET 160R 2015

Отзывы:

Похожие инструкции для CB HORNET 160R 2015

Бренды по названию

Популярные бренды

Honda CB HORNET 160R 2015, Руководство по ремонту

Результаты поиска

Содержание CB HORNET 160R 2015

Отзывы:

Похожие инструкции для CB HORNET 160R 2015

Бренды по названию

Популярные бренды