Honda CB HORNET 160R 2015 Скачать руководство пользователя страница 185

Страница: 185 / 336

11-13

CRANKCASE/TRANSMISSION/KICKSTARTER

Lubricate the all bearings with engine oil.

Drive new bearings into the right crankcase with following
tools.

TOOLS:
Crankshaft bearing:
Driver

070GD-001I100

Attachment, 52 x 55 mm

07NAD-P200100

Pilot, 30 mm

07746-0040700

INSTALLATION

Install the crankshaft into the right crankcase.

Install the transmission.

INSTALLATION

Clean all parts in solvent and dry them thoroughly.

Apply clean engine oil to each gear teeth.

Apply molybdenum oil solution to the bushing sliding
surface to ensure initial lubrication.

Assemble all parts into their original positions.

• Check the gears for freedom of movement or rotation

on the shaft.

• Install the washers and snap rings with the chamfered

edge facing the thrust load side. Confirm the inner

side of snap rings and washer when you detect the
chamfered side.

• Do not reuse worn snap ring which could easily spin

in the groove.

• Check that the snap rings are seated in the shaft

grooves, and align their end gaps with the grooves of
the spline.

CORRECT

SNAP RING

INCORRECT

DRIVER

ATTACHMENT

BEARING

CRANKSHAFT

Содержание CB HORNET 160R 2015

















































































































































































































































































































































Результаты поиска

Содержание CB HORNET 160R 2015

Отзывы:

Похожие инструкции для CB HORNET 160R 2015

Бренды по названию

Популярные бренды

Honda CB HORNET 160R 2015, Руководство по ремонту

Результаты поиска

Содержание CB HORNET 160R 2015

Отзывы:

Похожие инструкции для CB HORNET 160R 2015

Бренды по названию

Популярные бренды