Honda CB HORNET 160R 2015 Скачать руководство пользователя страница 89

Страница: 89 / 336

5-17

FUEL SYSTEM

6. Insert the probe into the muffler and measure the

carbon-mono-oxide (CO%) concentration.
CO measurement at idle: 0.7 – 0.8%
If the CO concentration is exist, adjust the pilot screw as

following.

7. Disconnect the vacuum hose of PAIR control valve, then
it connect the vacuum pump and plug the vacuum port.

Apply the specified vacuum to the PAIR control valve

vacuum hose more than 53.3 kPa (400 mm Hg) (make
sure the secondary air does not supply).

8. Start the engine and check the idle speed.

IDLE SPEED: 1,400 ± 100 min

-1

(rpm)

If the idle speed is out of specification, adjust the idle

speed by turning the throttle stop screw with the PAIR
system stopped.

9. Turn the pilot screw and adjust the CO concentration.

CO measurement at idle: (secondary air does not

supply) 1.5 - 3.8 %

10. Disconnect the plug from the vacuum port, then remove
the vacuum pump and connect the vacuum hose of PAIR
control valve.

Start the engine.
Adjust the idle speed with the throttle stop screw if
necessary.

IDLE SPEED: 1,400 ± 100 min

-1

(rpm)

Measure the CO concentration again.

CO measurement at idle: 0.7 - 0.8%

If the CO concentration is exist, check the secondary air

supply system (page 5-19).

When PAIR

system stop,

idle speed will

change.

CO MEASUREMENT TOOL

VACUUM HOSE

VACUUM

PUMP

PLUG

THROTTLE

STOP SCREW

Содержание CB HORNET 160R 2015

















































































































































































































































































































































Результаты поиска

Содержание CB HORNET 160R 2015

Отзывы:

Похожие инструкции для CB HORNET 160R 2015

Бренды по названию

Популярные бренды

Honda CB HORNET 160R 2015, Руководство по ремонту

Результаты поиска

Содержание CB HORNET 160R 2015

Отзывы:

Похожие инструкции для CB HORNET 160R 2015

Бренды по названию

Популярные бренды