Honda CB HORNET 160R 2015 Скачать руководство пользователя страница 202

Страница: 202 / 336

12-6

FRONT WHEEL/SUSPENSION/STEERING

Remove the bolts, handlebar upper holders and handlebar
from the top bridge.

BOLTS

HANDLEBAR

HOLDER

HANDLEBAR

HOLDER

PUNCH MARKS

Align

CLUTCH LEVER
BRACKET

Align

BOLT

HANDLEBAR GRIP

INSTALLATION

Place the handlebar to the top bridge.

Place the handlebar holders with the punch marks facing
forward and install the holder bolts.

Align the punch mark on the handlebar with the mating
surface of the lower holder.

Tighten the forward bolts first, then the rear bolts.

TORQUE: 22 N.m (2.2 kgf.m, 16 lbf.ft)

Slide and Install the clutch lever bracket by aligning the
meeting surface of the bracket with the punch mark on
the handle bar.

Tighten the clutch lever bracket bolt.

Apply Honda Bond A or its equivalent to the inside surface
of the grips and to the clean surface of the left handlebar.

Wait 3-5 minutes and install the grip.

Rotate the grips for even application of the adhesive.

Allow the

adhesive to dry

for 1 hour before

using.

Содержание CB HORNET 160R 2015

















































































































































































































































































































































Результаты поиска

Содержание CB HORNET 160R 2015

Отзывы:

Похожие инструкции для CB HORNET 160R 2015

Бренды по названию

Популярные бренды

Honda CB HORNET 160R 2015, Руководство по ремонту

Результаты поиска

Содержание CB HORNET 160R 2015

Отзывы:

Похожие инструкции для CB HORNET 160R 2015

Бренды по названию

Популярные бренды