Hioki ST5520 Скачать руководство пользователя страница 169

Страница: 169 / 201

161

ISO.COM

Internal GND

• External interface pin arrangement list (p. 84)

(3) TEST signal OFF timing setting

After a test, timing for the TEST signal output transistor to turn OFF from ON can be set.

FAST

The TEST signal turns OFF immediately after a test is completed

without waiting for the voltage between the measurement terminals to

drop.

SLOW

The TEST signal turns OFF after the voltage between the

measurement terminals drops below 10 V ± 3 V.

Refer to “Test duration accuracy” (p. 155).

EXT.SW (not isolated against the power supply protective ground terminal and

isolated against the measurement terminals)

The switch signal line plug of the 9299 Switched Probe is connected.

The operation mode can be switched between two modes, CONT and TRIG (the instrument

settings have priority).

Continuous (CONT)

mode

Measurement is performed only while the 9299 switch is being

pressed.

Trigger (TRIG) mode

A test starts and stops every time the 9299 switch is pressed.

RS-232C (not isolated against the power supply protective ground terminal and

isolated against the measurement terminals)

RMT

is displayed at the top of the screen during communications and any keys other than the

LOCAL key and STOP key are disabled.

Remote control and measured value output can be performed.

Output data setting: OFF/TYPE 1/TYPE 2

• TYPE1

Output: Measured value + judgment

• TYPE2

Output: Measured value (index display 000.0E+06)
(Same as

:MEASure?

query) (p. 125)

(1) RS-232C interface

Transfer method

Communications: Full duplex

Synchronization: Start-stop synchronization

Baud rate

9,600 bps (default) / 19,200 bps / 38,400 bps

Data length

8 bits

Parity

None

Stop bit

1 bit

Appx.

Ind.

Содержание ST5520










































































































































































































Результаты поиска

Содержание ST5520

Отзывы:

Hioki ST5520, Инструкция по эксплуатации, Страница: 169 / 201

Результаты поиска

Содержание ST5520

Отзывы: