Hioki ST5520 Скачать руководство пользователя страница 155

Страница: 155 / 201

147

Command Reference

:IO:ILOCk

Sets the interlock function.

Syntax

IO:ILOCk <data>

<data>

ON/OFF (text data)

ON: The interlock function is enabled.

OFF: The interlock function is disabled.

Example

To set the interlock function to ON

PC>

IO:ILOCk ON

:IO:ILOCk?

Queries the interlock function setting. The ON or OFF setting is returned in text data (<data>).

Syntax

IO:ILOCk?

Response

IO:ILOCK <data>

or simply

<data>

<data>

ON/OFF (text data)

ON: The interlock function is enabled.

OFF: The interlock function is disabled.

Example

To query the interlock function setting (when the setting is ON)

PC>

IO:ILOCk?

ST5520>

IO:ILOCK ON

(when the

:HEADer

command is ON)

ST5520>

(when the

:HEADer

command is OFF)

:SYSTem:KLOCk

Sets the key lock.

Syntax

:SYSTem:KLOCk <data>

<data>

ON/OFF (text data)

ON: The key lock is set.

OFF: The key lock is cancelled.

Example

To set the key lock
PC>

:SYSTem:KLOCk ON

Appx.

Ind.

Содержание ST5520










































































































































































































Результаты поиска

Содержание ST5520

Отзывы:

Hioki ST5520, Инструкция по эксплуатации, Страница: 155 / 201

Результаты поиска

Содержание ST5520

Отзывы: