Hioki ST5520 Скачать руководство пользователя страница 124

Страница: 124 / 201

116

Using the RS-232C Interface

When connecting the instrument with a computer

Use a crossover cable with 9-pin D-sub (socket contacts) connectors.

Crossover wiring

DCD

RxD

TxD

DTR

GND

DSR

RTS

CTS

DCD

RxD

TxD

DTR

GND

DSR

RTS

CTS

9-pin D-

sub

(socket contacts)

Instrument side

9-pin D-sub

(socket contacts)

IBM PC compatible

computer

Pin No.

Recommended cable: Hioki 9637 RS-232C Cable (9pin-9pin/1.8 m)

When connecting a controller with a 25-pin D-sub port

Use a crossover cable with a 9-pin D-sub (socket contacts) and a 25-pin D-sub (pin

contacts) connector.

As in the figure shown below, the RTS and CTS pins are shorted and crossed to the

DCD in the other connector.

DCD

RxD

TxD

DTR

GND

DSR

RTS

CTS

TxD

RxD

RTS

CTS

DSR

GND

DCD

DTR

9-p

in D-sub female

Instrument side

25-pin D-sub male

Controller side

Pin No.

Recommended cable: Hioki 9638 RS-232C Cable (9pin-25pin/1.8 m)

The combination of a dual 25-pin D-sub (pin contacts) cable and a 9-pin to 25-pin

adapter cannot be used.

Содержание ST5520










































































































































































































Результаты поиска

Содержание ST5520

Отзывы:

Hioki ST5520, Инструкция по эксплуатации, Страница: 124 / 201

Результаты поиска

Содержание ST5520

Отзывы: