Hioki ST5520 Скачать руководство пользователя страница 99

Страница: 99 / 201

Timing Chart

Item

Time

START, STOP signal pulse width

5 ms

MIN.

START, STOP signal detection time

5 ms

MAX.

t3 Response time (DELAY)

AUTO, 5 ms to 999.9 s

t4 Measurement

time

Contact check: OFF

30 ms (FAST), 480 ms (SLOW)

Contact check: ON

80 ms (FAST), 480 ms (SLOW)

t5 Measurement

interval

Contact check: OFF

50 ms (FAST), 500 ms (SLOW)

Contact check: ON

100 ms (FAST), 500 ms (SLOW)

Discharge time (time for the output voltage to drop

below 10 V)

20 ms

MAX.

(during pure resistance

measurement)

t7 Test duration (TIMER)

45 ms to 999.9 s

When the START signal is input after the test voltage is changed, a time of up to 500 ms is
added to detect the START signal.

PASS STOP mode timing chart

When the test duration setting (TIMER) is ON and the measurement is performed by the /START
signal input from EXT.I/O or when the test duration setting (TIMER) is ON and the measurement
is performed by the START key on the panel

Setting

Test duration (TIMER) Response time (DELAY)

TEST signal OFF timing

ON, 45 ms to 999.9 s

AUTO, 5 ms to 999.9 s

FAST

When the test duration (TIMER) is set to OFF, tests are performed continuously
until a PASS judgment is made.

Appx.

Ind.

Содержание ST5520










































































































































































































Результаты поиска

Содержание ST5520

Отзывы:

Hioki ST5520, Инструкция по эксплуатации, Страница: 99 / 201

Результаты поиска

Содержание ST5520

Отзывы: