Hioki ST5520 Скачать руководство пользователя страница 177

Страница: 177 / 201

169

Troubleshooting

Others

Symptom

Cause and solution

Reference

The power does

not turn on.

The power may not be supplied.

• Check the power cord.

• Check that the facility breaker is on.

• Turn on the power switch (rear side).

The power voltage and frequency may not be correct.

Check the power rating. (100 V to 240 V, 50/60 Hz)

The key operation

cannot be

performed.

[LOCK]

is displayed.

• When the key lock function is set to ON, disable the

function.

p. 65

• When the interlock function is set to ON, switch it to OFF.

To disable the interlock function, turn on the power while

holding down the MENU key and down key. Otherwise,

send the communication command,

:IO:ILOCk OFF

p. 106

• While a LOAD signal is input, the instrument enters the key

lock state, accepting no key operations.

p. 86

[RMT]

is displayed.

Reset the remote.

p. 119

[LOCK]

is displayed.

Release the interlock.

• How to release the interlock

Turn on the power while pressing the MENU + Down keys.

The interlock can also be released using the “

:IO:ILOCk

OFF

” communication command.

p. 106

The COMP lamp

does not turn on.

When the measured value is displayed, the upper or lower

limit value may not be set. Set the upper or lower limit value.

p. 44

When the measured value is not displayed, an appropriate

measurement range may not be automatically defined.

Extend the test duration.

p. 39

A contact check

error occurs.

The probe wires may be broken.

Check the probe using a tester.

The contact resistance between the measurement terminal

and contact check terminal may be high.

The equipment to be measured may not be in contact. Check

the wiring again.

Appx.

Ind.

Содержание ST5520










































































































































































































Результаты поиска

Содержание ST5520

Отзывы:

Hioki ST5520, Инструкция по эксплуатации, Страница: 177 / 201

Результаты поиска

Содержание ST5520

Отзывы: