Hioki ST5520 Скачать руководство пользователя страница 83 | Manualshive

Страница: 83 / 201

Hioki ST5520 Скачать руководство пользователя страница 83

75

6

Saving and Loading Measurement
Conditions (Memory function)

Panel save function

The current measurement conditions can be saved.
Up to 10 patterns of measurement conditions can be saved and retained even when
the power is turned off.

Settings that can be saved with the panel save function

•

Test voltage

• Range (including auto range ON/OFF and resistance range for the fixed range)

•

Test speed

•

Test duration

•

Response time

• Comparator upper and lower limit values (including comparator ON/OFF)

•

Test mode

•

Judgment beep sound

Panel load function

The measurement conditions saved by the panel save function are loaded.
The measurement conditions can be loaded by the operation key, RS-232C
command, or EXT.I/O.

6

Saving and Loading Measurement Conditions (Memory function)

10

9

8

7

6

5

4

3

2

1

Appx.

Ind.

«
...
81
82
83
84
85
...
»

Содержание ST5520










































































































































































































Отзывы:

Нет отзывов