Hioki ST5520 Скачать руководство пользователя страница 173

Страница: 173 / 201

165

Maintenance and Service

10.1 Maintenance

WARNING

Some of the internal components carry high voltage, which is very
hazardous. Customers are not allowed to modify, disassemble, or

repair the instrument. Doing so may cause fire, electric shock, or

injury.

Calibrations

IMPORTANT

Periodic calibration is necessary in order to ensure that the instrument provides

correct measurement results of the specified accuracy.

The calibration frequency varies depending on the status of the instrument or

installation environment. We recommend that the calibration frequency be determined

in accordance with the status of the instrument or installation environment and that

you request that calibration be performed periodically.

Transporting

• When shipping the instrument, use the packing materials used when the instrument

was delivered.

• Pack the instrument so that it is not damaged during shipping and include a

description of existing damage. Hioki cannot be responsible for damage that occurs

during shipping.

Cleaning

• To clean the instrument and optional equipment, wipe them gently with a soft cloth

moistened with water or mild detergent.

• Wipe the display gently with a soft, dry cloth.

IMPORTANT

Never use solvents such as benzene, alcohol, acetone, ether, ketones, thinners, or

gasoline. They can deform and discolor the instrument.

Disposal

Handle and dispose of the instrument and optional equipment in accordance with

local regulations.

10 Maintenance and Service

Appx.

Ind.

Содержание ST5520










































































































































































































Результаты поиска

Содержание ST5520

Отзывы:

Hioki ST5520, Инструкция по эксплуатации, Страница: 173 / 201

Результаты поиска

Содержание ST5520

Отзывы: