Hioki ST5520 Скачать руководство пользователя страница 134

Страница: 134 / 201

126

Command Reference

8.6 Command Reference

Command reference description

Syntax

:MOHM:RANGe <data>

Reference

Specifies the syntax for the command.

<>:

Specifies the description of the message data (text or numerical

parameter). A response is returned in capital letters for a text parameter.

Numerical parameter:

NRf: Format including NR1, NR2, and NR3.

NR1: Integer data (example: +12, -23, 34)

NR2: Decimal data (example: +1.23, -23.45, 3.456)

NR3: Floating decimal point index data (example: +1.0E-2, -2.3E+4)

<data>

2 M / 20 M / 200 M / 2000 M / 4000 M / AUTO (text data)

Reference

Explains parameter data.

Example

Set to 200 M

range.

PC>

:MOHM:RANGe 200M

Reference

Example of the use of the command
PC> indicates a command from the computer.

ST5520> indicates a response from the ST5520.

Error

An execution error occurs if the 2000 M

range is executed when the test

voltage is between 25 V and 99 V.

Reference

Explains the error.

Program message

Response message

Содержание ST5520










































































































































































































Результаты поиска

Содержание ST5520

Отзывы:

Hioki ST5520, Инструкция по эксплуатации, Страница: 134 / 201

Результаты поиска

Содержание ST5520

Отзывы: