manualshive.com logo in svg

Hioki ST5520, Инструкция по эксплуатации, Страница: 64 / 201

Поделиться
Скачать
Hioki ST5520 Скачать руководство пользователя страница 64

56

Checking Faulty Contact and Contact Status (Contact check function)

5.1 

Checking Faulty Contact and Contact Status 
(Contact check function)

The faulty contact of the equipment to be measured and probes and the broken wires 
of the measurement cables are detected.
The measurement terminals on the rear panel of the instrument are used for contact 
check. The contact check function monitors the contacts from the start to the end of 
measurement in every sampling and can detect faulty contacts and broken wires of 
the probes not only before and after tests but also during the tests. If faulty contacts 
are detected, a contact error (ContLo M

Ω

, ContHi M

Ω

, or ContHL M

Ω

) is displayed 

in the measured value display section, and the test stops.  (The ERR signal is output 
from EXT.I/O.) When this error is displayed, check the probe contact and for any 
broken wires of the measurement cables. (The instrument needs to be repaired if the 
error does not disappear even when the measurement cables that are not broken are 
short circuited.)

IMPORTANT

 

•

Even if the measurement speed is set to 

[FAST]

, the sampling time takes 100 

ms when the contact check function is ON. (The sampling time is 500 ms if the 
measurement speed is set to 

[SLOW]

 regardless of the function check setting.)

 

•

When the contact check function is set to OFF, a measured value is displayed 
even if the probe is not in contact with the equipment to be measured.

 

•

If the set test duration is shorter than the sampling time, a proper measurement 
cannot be performed. (The measured value may not be displayed.) Set a test 
duration that is longer than the sampling time.

Содержание ST5520










































































































































































































Отзывы:

Нет отзывов