Hioki ST5520 Скачать руководство пользователя страница 168

Страница: 168 / 201

160

•

Signals

START

Starts a test and generates output voltage.

STOP

Ends a test and cuts off output voltage.

INTERLOCK

Open when the interlock function is enabled, short circuit when the

interlock function is disabled.

LOAD0 to LOAD3

Selects a test condition from saved test conditions.

(2) Output

• Common specifications

Photocoupler-isolated, open drain output (non-polar)

Maximum load

voltage

30 V DC

MAX

Residual voltage 1 V or less (load current 50 mA) / 0.5 V or less (load
current 10 mA)

Maximum output

current

50 mA

MAX

/ch

•

Signals

PASS

The output transistor is ON when comparator PASS judgment is made.

UPPER FAIL

The output transistor is ON when comparator UPPER FAIL judgment

is made.

The output transistor is ON when comparator UL_FAIL judgment is

made.

LOWER FAIL

The output transistor is ON when comparator LOWER FAIL judgment

is made.

The output transistor is ON when comparator UL_FAIL judgment is

made.

TEST

The output transistor is ON during a test.

The output transistor is ON or OFF during discharge depending on the

TEST signal OFF timing setting.

ERR

The output transistor is ON at the time of a contact check error, short

circuit error, output voltage error judgment

(ST5520-01 only)
DP0 to DP2

Decimal point output 3 bits (p. 87)

BCD0 to BCD15

BCD output 4 digits, 16 bits (p. 87)

•

Internal power output

Output voltage

Sink current output compatible 5.0 V±10%

Source current output compatible -5.0 V±10%, 100 mA

MAX

Isolation

Floating from protective ground potential and measurement circuit

Isolation rating

Terminal to ground voltage 50 V DC, 33 V AC

RMS

, and 46.7 V AC

PEAK

or less

ISO.5 V

Internal power supply

Содержание ST5520










































































































































































































Результаты поиска

Содержание ST5520

Отзывы:

Hioki ST5520, Инструкция по эксплуатации, Страница: 168 / 201

Результаты поиска

Содержание ST5520

Отзывы: