Hioki ST5520 Скачать руководство пользователя страница 44

Страница: 44 / 201

Setting the Range

3.2 Setting the Range

There are two range settings, auto and manual. For the manual range setting, the
range can be chosen from 2 M

, 20 M

, 200 M

, 2000 M

, and 4000 M

. Note,

however, that the ranges that can be set varies depending on the test voltage. (p. 153)

The auto range may require some time before a measured value is displayed as the
range has to shift after a test starts. To eliminate this time, set the range manually
according to the object to be measured.

Setting the manual range

Open the Settings screen.

Select

[SET]

Set

[RANGE]

[HOLD]

Selection

[HOLD]

Return to the
Measurement
screen.

Select the range.

Item selection

Select the range.

Return to the
Measurement
screen.

When analog output is used, 0 to 4 V is output from the analog output terminal according to

each resistance range. (p. 105)

Содержание ST5520










































































































































































































Результаты поиска

Содержание ST5520

Отзывы:

Hioki ST5520, Инструкция по эксплуатации, Страница: 44 / 201

Результаты поиска

Содержание ST5520

Отзывы: