Hioki ST5520 Скачать руководство пользователя страница 166

Страница: 166 / 201

158

Test mode

Switch a mode selecting from continuous mode, PASS STOP mode,

FAIL STOP mode, or forced termination judgment mode.

•

Continuous mode

Measurement is performed for the specified test duration, judgment

is performed for each measurement, the judgment result is output,

and the output voltage is cut off.

The displayed measured value and judgment result display are held

as they are at the end of a test.

• PASS STOP mode

A test is completed when a PASS judgment is made and the output

voltage is cut off.

The displayed measured value and PASS display are held as they

are at the end of the test.

• FAIL STOP mode

A test is completed when a FAIL judgment is made and the output

voltage is cut off.

The displayed measured value and FAIL display are held as they are

at the end of the test.

•

Forced termination judgment mode

The judgment result based on the upper and lower limit values is

displayed after the setting time elapsed or at the time of STOP is

input (key, RS command, or EXT.I/O).

Judgment result is output on the display, via RS command, or via

EXT.I/O.

The displayed measured value and judgment result display are held

as they are at the end of a test.

Double action

Operation

The

START

key is enabled only for 1 s after the

STOP

key is pressed.

Key lock function

Reset means

Hold down the

[UNLOCK]

key (for 1 s) when the key lock function is

enabled.

Display

[LOCK]

is displayed at the top of the screen when the key lock

function is enabled.

(The START key and STOP key are enabled.)

Interlock function

Display

[LOCK]

is displayed at the top of the screen when the interlock

function is enabled.

Operation

No key operations are enabled.
No tests can be started via EXT.I/O or RS command.

Содержание ST5520










































































































































































































Результаты поиска

Содержание ST5520

Отзывы:

Hioki ST5520, Инструкция по эксплуатации, Страница: 166 / 201

Результаты поиска

Содержание ST5520

Отзывы: