Hioki ST5520 Скачать руководство пользователя страница 60

Страница: 60 / 201

Measured Value Display

4.3

Measured Value Display

A measured value outside of the accuracy range can also be displayed.

Measurement voltage

Display range

25 V ≤ V 100 V

0.000 M

to 400.0 M

100 V ≤ V 500 V

0.000 M

to 4000 M

500 V ≤ V ≤ 1000 V

0.000 M

to 9990 M

When the measure value is outside of the display range, “Over.F” or “Under.F” is

displayed.

Refer to “9 Specifications” (p. 151) for the accuracy range.

IMPORTANT

•

The guaranteed accuracy range is different from the display range.

•

When the range is set to

AUTO, it may take time to display a measured value

immediately after a test starts due to range shift. To check a measured value

immediately, set the range to MANUAL.

(Refer to “3.2 Setting the Range” (p. 36) for the setting procedure.)

• If PASS/FAIL judgment is obtained with a command in the auto range when the

range is not set or before a measured value is displayed, ULFAIL (no judgment)

is returned. Extend the test duration.

•

When test terminates without the range having been determined while using

auto-ranging, no measured value will be displayed. Use a longer test time.

• In the auto range, the measured value may fluctuate between two ranges. Set

the range to MANUAL.

• “Over.F” (overflow) is displayed when the measured value exceeds the display

range maximum value in the auto range and when the measured value exceeds

the maximum display value in each range in the MANUAL range.

• “Under.F” (underflow) is displayed when the measured value is less than190 dgt.

in the MANUAL range excluding 2 M

range. “Under.F” is not displayed in the

AUTO range.

•

The more electrostatic capacitance components the equipment to be measured

contains, the more the measured value fluctuates. Also it takes for an output

voltage to rise.

•

When the processing is performed at high speed (for example, the test duration

is less than 100 ms), there is a possibility that the voltage monitor cannot be

updated in time. To check the output voltage, monitor the waveform on an

Содержание ST5520










































































































































































































Результаты поиска

Содержание ST5520

Отзывы:

Hioki ST5520, Инструкция по эксплуатации, Страница: 60 / 201

Результаты поиска

Содержание ST5520

Отзывы: