Hioki ST5520 Скачать руководство пользователя страница 61

Страница: 61 / 201

Completing Measurement

4.4 Completing Measurement

WARNING

To avoid electric shock, remove the measurement leads from an
equipment to be measured after the TEST lamp is turned off after a
test.

Tests are completed by one of the following.

•

The

STOP

key is pressed, the EXT.I/O STOP signal is LOW, or a test

completion command is sent from the RS-232C.

•

The set test duration elapses.

• The test mode is set to FAIL STOP mode and FAIL judgment is made.

•

The test mode is set to PASS STOP mode and a PASS judgment is made.

•

The test mode is set to PASS STOP mode and PASS judgment is made.

•

The

*RST

, or

:STOP

command or a command related to test conditions

(

:TIMer

:DELay

, etc.) is sent from the RS-232C interface.

The measured value and COMP lamp displayed immediately before the
test is completed continue to be displayed.

The TEST lamp may not turn off and continue to blink even after the test
is completed. This indicates that any charge remaining in the equipment

to be measured and instrument is being released. Follow “4.5 Automatic

discharge function” to release any remaining charge.

After the TEST lamp turns off, remove the test leads.

Appx.

Ind.

Содержание ST5520










































































































































































































Результаты поиска

Содержание ST5520

Отзывы:

Hioki ST5520, Инструкция по эксплуатации, Страница: 61 / 201

Результаты поиска

Содержание ST5520

Отзывы: