Hioki ST5520 Скачать руководство пользователя страница 101 | Manualshive

Страница: 101 / 201

Hioki ST5520 Скачать руководство пользователя страница 101

93

Timing Chart

FAIL STOP mode timing chart

When the test duration setting (TIMER) is ON and the measurement is performed by the /START
signal input from EXT.I/O or when the test duration setting (TIMER) is ON and the measurement
is performed by the START key on the panel

Setting

Test duration (TIMER) Response time (DELAY)

TEST signal OFF timing

ON, 45 ms to 999.9 s

AUTO, 5 ms to 999.9 s

FAST

When the test duration (TIMER) is set to OFF, tests are performed continuously
until a FAIL judgment is made.

Measurement-1

Measurement-2

10 V

t1

t2

t6

t3

t5

t4

/START

(Input)

/TEST

(Output)

Test voltage

Measured

value display

/PASS

(Output)

/U.FAIL

/L.FAIL

(Output)

/ERR

(Output)

t7

Measurement end

When the TEST signal OFF
timing setting is SLOW

When measured

value-1 result is PASS

When measured

value-2 result is FAIL

Previous measured value

Previous result

Previous result

Previous result

OFF

ON

OFF

OFF

OFF

ON

OFF

0/0.0/0.00 M

Ω

Measured value-1

Measured value-2

Measurement-1 contact check result

Measurement,

judgment

(including

contact check)

10

9

8

7

6

5

4

3

2

1

Appx.

Ind.

«
...
99
100
101
102
103
...
»

Содержание ST5520










































































































































































































Отзывы:

Нет отзывов