Hioki ST5520 Скачать руководство пользователя страница 119

Страница: 119 / 201

111

Accessory Connector Assembly

7.9 Accessory Connector Assembly

The EXT.I/O connector and covers, etc. are supplied with the instrument. Assemble
the connector according to the following procedure.

•

Use a shielded cable to connect the EXT.I/O connector and a PLC, etc. If a

shielded cable is not used, the influence of noise could cause the system to

malfunction.

•

Connect the shield to the ISO_COM terminal of EXT.I/O.

•

If any of the supplied screws are missing or damaged, contact your authorized
Hioki distributor or reseller.

Required items

•

Screwdriver

•

Shielded cable

•

Soldering iron

Accessories

•

Cover

1 set (2 pieces)

•

Screw (+/-) #4-40UNC (length: 16.9 mm) 2 pieces

•

Screw (+/-) #4-40UNC (length: 12.6 mm) 2 pieces

•

Screw (-) #4-40UNC (length: 15.0 mm)

2 pieces

•

Nut #4-40UNC

2 pieces

•

Retainer (for cable)

2 pieces

•

Retainer (case protection)

2 pieces

•

Connector

1 piece

Assembly procedure

Solder the cable (shielded cable) to connector (H) of EXT.I/O.

Attach retainers (F) to the cable using screws (C).

Position retainers (F) according to the specified positions of covers (A).

4. Insert screws (D) through retainers (G).
5. Place connector (H), retainers (F), retainers (G), and screws (D) on one of covers (A).

Place the other cover (A).

7. Secure covers (A) using screws (B) and nuts (E). Note that tightening the screws

excessively can damage the covers.

Appx.

Ind.

Содержание ST5520










































































































































































































Результаты поиска

Содержание ST5520

Отзывы:

Hioki ST5520, Инструкция по эксплуатации, Страница: 119 / 201

Результаты поиска

Содержание ST5520

Отзывы: