Hioki ST5520 Скачать руководство пользователя страница 111

Страница: 111 / 201

103

Checking External Control

7.5 Checking External Control

Performing an I/O test (EXT.I/O test function)

In addition to switching output signals between ON and OFF manually, the input
signal status can be viewed on the screen.

Open the Settings screen.

Select

[SET]

Select the operation mode for

[EXT.I/O TEST]

Selection

Execute

Return to the
Measurement
screen.

Perform the EXT.I/O test.

Select the signal.

Turn ON the signal.

Turn OFF the
signal.

Return to the EXT.I/O
Settings screen.

Output signals

Allows you to perform signal operations.
(ON: Reverse display, OFF: Normal display)

Input signals

Displays the signal status. (ON: Reverse display, OFF: Normal display)

Displays LOCK in reverse video.

(ON: Normal display, OFF: Reverse display)

Appx.

Ind.

Содержание ST5520










































































































































































































Результаты поиска

Содержание ST5520

Отзывы:

Hioki ST5520, Инструкция по эксплуатации, Страница: 111 / 201

Результаты поиска

Содержание ST5520

Отзывы: