Hioki ST5520 Скачать руководство пользователя страница 151

Страница: 151 / 201

143

Command Reference

:SYSTem:LFRequency

Sets the power frequency.

When AUTO is set, 50 Hz and 60 Hz are automatically identified.

Syntax

:SYSTem:LFRequency <data>

<data>

AUTO/50/60 (text data)

AUTO: The power frequency is automatically identified.

50: Power frequency 50 Hz

60: Power frequency 60 Hz

Example

To set the power frequency to 60 Hz

PC>

:SYSTem:LFRequency 60

:SYSTem:LFRequency?

Queries the power frequency setting. The setting is returned in NR1 number data (<data>).

Syntax

:SYSTem:LFRequency?

Response

:SYSTEM:LFREQUENCY <data>

or simply

<data>

<data>

AUTO/50/60 (text data)

Example

To query the power frequency setting (when the power frequency is 60 Hz)

PC>

:SYSTem:LFRequency?

ST5520>

:SYSTEM:LFREQUENCY 60

(when

the

:HEADer

command is ON)

ST5520>

(when the

:HEADer

command is OFF)

:PANel:LOAD

Loads the test conditions with the specified number. During a test, the test is stopped and the

test conditions are loaded.

Syntax

:PANel:LOAD <data>

<data>

Test condition number 1 to 10 (NR1 numerical data)

Example

To load No. 3 test conditions
PC>

:PANel:LOAD 3

:PANel:SAVE

Saves the test conditions with the specified number.

Syntax

:PANel:SAVE <data>

<data>

1 to 10 (NR1 numerical data)

Example

To save as No. 3
PC>

:PANel:SAVE 3

Appx.

Ind.

Содержание ST5520










































































































































































































Результаты поиска

Содержание ST5520

Отзывы:

Hioki ST5520, Инструкция по эксплуатации, Страница: 151 / 201

Результаты поиска

Содержание ST5520

Отзывы: