manualshive.com logo in svg

Hioki ST5520, Инструкция по эксплуатации, Страница: 187 / 201

Поделиться
Скачать
Hioki ST5520 Скачать руководство пользователя страница 187

Appx.

7

Influence of Noise

Appx. 6 

Influence of Noise

When induction noise is caused by commercial power supply

Induction noise caused by a commercial power supply is generated by not only commercial 

power lines or power outlets but also by fluorescent lights and household electrical appliances. 

The noise caused by a commercial power supply depends on the frequency of the power supply 
and is generated at a frequency of 50 Hz or 60 Hz.

To reduce the influence of noise caused by the commercial power supply, a method for 

converting the integration time to the integral multiple of the power frequency is generally used. 

(Figure. Noise caused by commercial power supply)

The measurement speed of this instrument is FAST or SLOW. In a high resistance 
measurement, the measured value may not be stabilized. In such a case, reduce the 
measurement speed or take appropriate measures to reduce noise.
If the instrument is used with a power frequency setting of 60 Hz in a 50 Hz area, the measured 

value fluctuates even if the measurement speed is set so that the integration time becomes the 

integral multiple of the power frequency. Check the instrument power frequency setting.

Measurement signal superimposed on power supply noise

Ideal measurement 
signal (direct current)

Integration time

Figure. Noise caused by commercial power supply

10

9

8

7

6

5

4

3

2

1

Appx.

Ind.

Содержание ST5520










































































































































































































Отзывы:

Нет отзывов