Hioki ST5520 Скачать руководство пользователя страница 163

Страница: 163 / 201

155

Test duration

Definition of test

duration

Test duration = Response time + Measurement time

Setting range

0.045 s (45 ms) to 999.999 s

Test duration

ON/OFF (- -)

Display

000.000 s setting

Screen display: 000.0 s, 0.000 s if less than 100 ms

“000.0 s” is displayed when OFF is set, “HOLD” is displayed at the end

of a test.

Operation

The test duration counts down from the specified time after a test

starts.

When OFF is set, the test duration counts up after a test starts.

“999.9 s” is displayed when the test duration exceeds the display

range.

Guaranteed

accuracy range

0.050 s (50 ms) to 999.999 s

Set resolution

1 ms

Test duration

accuracy

±0.005 s (setting range 0.045 s to 0.099 s)

±0.05 s (setting range 0.100 s to 9.999 s)

±0.5 s (setting range 10.000 s to 999.999 s)

Voltage (V)

Set voltage

Response time

Charge time

Measurement time

Discharge time

Test duration

Time (t)

FAST

SLOW

Time diagram

(FAST, SLOW: TEST signal OFF timing setting)

Appx.

Ind.

Содержание ST5520










































































































































































































Результаты поиска

Содержание ST5520

Отзывы:

Hioki ST5520, Инструкция по эксплуатации, Страница: 163 / 201

Результаты поиска

Содержание ST5520

Отзывы: