Hioki RM3545 Скачать руководство пользователя страница 297

Страница: 297 / 364

14.1 Troubleshooting

289

3. EXT I/O issues
The EXT I/O test (p.215) function can be used to more easily check operation.

Issue

Items to check

Possible causes

→

Solutions

See

3-1 The instrument is

not operating at
all.

The IN and OUT values displayed on
the instrument’s EXT I/O test do not
agree with the controller.

The wiring is incorrect.

→

Check EXT I/O (p.175) again.

• A connector is disconnected.
• A pin number is incorrect.
• ISO-COM pin wiring
• NPN/PNP setting
• Contact (or open collector) con-

trol (voltage does not provide
control)

• Supply of power to the controller

(power cannot be supplied to the
instrument)

p.175

3-2 The TRIG signal

is not working.

The trigger source is set to the internal
trigger (INT).

If the internal trigger setting is
being used, the TRIG signal will not
serve as a trigger.

→

Select the external trigger set-

ting.

p.206

The TRIG ON time is less than 0.1 ms. The TRIG ON time is too short.

→

Ensure that the ON time is at

least 0.1 ms.

The TRIG OFF time is shorter than 1
ms.

The TRIG OFF time is too short.

→

Ensure that the OFF time is at

least 1 ms.

The TRIG/PRINT signal filter function
is ON.

A longer signal control time is
required.

→

Increase the signal ON time.

→

Turn OFF the filter function.

p.210

The

:INIT:CONT

(command) is OFF. The instrument is not in the trigger

wait state.

→

Send the

:INIT

:READ?

command.

3-3 The instrument

will not print.

The interface setting is not set to the
printer.

The setting must be configured.

→

Set the interface to the printer.

p.239

The TRIG/PRINT signal filter function
is ON.

A longer signal control time is
required.

→

Turn OFF the function.

p.210

3-4 The instrument

will not load panel
data.

No panel has been saved using the
panel number that you are trying to
load.

The instrument cannot load a panel
that has not been saved.

→

Change the LOAD signal or re-

save the panel before the LOAD
signal is asserted.

3-5 The channels

cannot be
switched with the
LOAD signal.

The channel numbers have not been
set.
The channels have been disabled.
The scan function has been turned off.

The scan settings have been
improperly configured.

→

Check the scan settings.

p.148

Содержание RM3545













































































































































































































































































































































































Результаты поиска

Содержание RM3545

Отзывы:

Hioki RM3545, Инструкция по эксплуатации, Страница: 297 / 364

Результаты поиска

Содержание RM3545

Отзывы: