manualshive.com logo in svg

Hioki DM7275 Series, Инструкция по эксплуатации

Поделиться
Скачать
Hioki DM7275 Series Скачать руководство пользователя страница 34

29

Turning the Instrument On and Off

Canceling the SLEEP state

Press the POWER button while the 

instrument is in the SLEEP state.

The POWER button will turn green.

Lighting-up in  red

To make measurements at the accuracy described in the instrument’s specifications, allow the 

instrument to warm up for at least 60 minutes after turning on the main power switch or canceling 

the SLEEP state. 

When the main power switch is turned on or the SLEEP state is canceled, the self-test (a series of 

self-diagnostics performed by the instrument) will start automatically. 

Self-test

The following information is displayed on the screen during 

the self-test:

 •Manufacturer name and model number

 •Software version

 •Communications interface settings

 •Detected power supply frequency

 •EXT I/O (NPN/PNP) setting

No error found

Error found

Measurement screen

Error indicate

d (p. 176)

 • The following options are available for the measurement conditions that are loaded after the 

self-test completes: “Use settings in effect when instrument was turned off,” “Use factory default 

settings,” and “Load specified panel.” (For more information about the default settings, see “7.7 

Selecting Startup Load Settings and a Panel” (p. 91).)

 • The instrument’s power supply frequency setting is automatically set to the power supply’s 

frequency.

(This setting can also be changed manually: See “7.6 Setting the Power Supply Frequency” 

(p. 90).)

2

Preparing for Measurement

www.

.com

[email protected]

1.800.561.8187

Содержание DM7275 Series
















































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды