Hioki DM7275 Series Скачать руководство пользователя страница 115

Страница: 115 / 207

113

Data Output Settings

9.3 Data Output Settings

(Measurement screen)

MENU

I/F

Enable automatic output.

(Default setting:

OFF

)

When automatic output is set to

, do not

use communications commands. Doing so

may cause measured value data to be sent

twice.

(To change the information that will be

output)

MEASUREMENT

ITEM

: Voltage value (default

setting)

V, TEMP

: Voltage value

and temperature

DATE-TIME

Measurement time and

date (default setting:

OFF

[output disabled])

COMP

CONDITION

ALL

: All judgments (default

setting)

: HI judgments

: IN judgments

: LO judgments

: HI and LO judgments

•If comparator judgment or BIN measurement

is set to

, judgment results will also be

output.

•When the interface is set to

USB KEYBD

DATE-TIME

is not output.

(To change the output format)

See “7.8 Setting Output Formats” (p. 92).

Outputting Data

www.

.com

[email protected]

1.800.561.8187

Содержание DM7275 Series
















































































































































































































Результаты поиска

Содержание DM7275 Series

Отзывы:

Бренды по названию

Популярные бренды

Hioki DM7275 Series, Инструкция по эксплуатации

Результаты поиска

Содержание DM7275 Series

Отзывы:

Бренды по названию

Популярные бренды