Hioki DM7275 Series Скачать руководство пользователя страница 197

Страница: 197 / 207

Appx.

Rack Mounting

Installation instructions

Be careful not to lose the parts removed from the instrument as you may need to use them again.

WARNING

To prevent damage to the instrument and electric shock, observe the following

precautions when choosing screws:

•

When installing the rack-mounting brackets on the sides of the instrument,

use screws with a nominal length that does not exceed the thickness of the

bracket by more than 3.5 mm (so that the screw does not protrude into the

instrument by more than 3.5 mm).

•

When removing the rack-mounting brackets and restoring the instrument

to its bench-top configuration, use the screws with which the instrument

shipped at the time of purchase (feet: M3 × 8 mm; sides: M4 × 6 mm). If those

screws are lost or damaged, please contact your authorized Hioki distributor

or reseller.

When installing the instrument in a rack, use a commercially available shelf or other suitable part

to ensure adequate strength.

(1)

Remove the feet on the bottom of the instrument and the screws from the side

covers.

Screws (bottom: four M3 × 8 mm screws; sides: four M4 × 6 mm screws)

Appx.

索

www.

.com

[email protected]

1.800.561.8187

Содержание DM7275 Series
















































































































































































































Результаты поиска

Содержание DM7275 Series

Отзывы:

Бренды по названию

Популярные бренды

Hioki DM7275 Series, Инструкция по эксплуатации

Результаты поиска

Содержание DM7275 Series

Отзывы:

Бренды по названию

Популярные бренды