Hioki DM7275 Series Скачать руководство пользователя страница 15

Страница: 15 / 207

Operating Precautions

Before connecting a measurement cable

DANGER

Measurement cables should only be connected to the secondary side of a

breaker. Any short-circuit current at the secondary side will be cut-off by the

breaker. Connections should never be made to the primary side of a breaker,

because unrestricted current flow could damage the instrument and facilities if a

short circuit occurs.

WARNING

To avoid electric shock and short-circuit accidents, use only the specified measurement

cables to connect the instrument input terminals (HIGH and LOW terminals) to the

circuit over 70 V DC to be tested.

Before connecting a temperature sensor

IMPORTANT

Connect the temperature sensor by inserting the plug all the way in the TEMP.SENSOR

connector. Insufficient connection may cause larger errors in measured values.

Before turning the power ON

WARNING

Before turning the instrument on, make sure the supply voltage matches that

indicated on its power connector. Connection to an improper supply voltage may

damage the instrument and present an electrical hazard.

CAUTION

Avoid using an uninterruptible power supply (UPS) or DC/AC inverter with rectangular

wave or pseudo-sine-wave output to power the instrument. Doing so may damage the

instrument.

Appx.

Ind.

www.

.com

[email protected]

1.800.561.8187

Содержание DM7275 Series
















































































































































































































Результаты поиска

Содержание DM7275 Series

Отзывы:

Бренды по названию

Популярные бренды

Hioki DM7275 Series, Инструкция по эксплуатации

Результаты поиска

Содержание DM7275 Series

Отзывы:

Бренды по названию

Популярные бренды