Hioki DM7275 Series Скачать руководство пользователя страница 114

Страница: 114 / 207

112

Output Methods

9.2 Output Methods

Configure the interface and EXT I/O and

connect the instrument.

USB COM

USB KEYBD

See “Using the USB interface” (p. 98).

RS-232C

See “Using the RS-232C interface”

(p. 100).

LAN

See “Using the LAN interface” (p. 104).

PRINTER

See “12 Printing” (p. 143).

EXT I/O (when inputting the TRIG

signal):

See “11 External Control (EXT I/O)”

(p. 125).

Configure the instrument.

Set the automatic output setting (

DATA

OUT

) to

(When selecting

PRINTER

, this step is not

necessary.)

See “9.3 Data Output Settings” (p. 113)

Prepare the device to which the

instrument will be connected.

USB COM

LAN

RS-232C

Place the device to which the

instrument will be connected in the

receive standby state. If connecting the

instrument to a computer, launch the

application and place it in the receive

standby state.

USB KEYBD

Launch the application, text editor, or

spreadsheet.

2. Place the cursor at the position in

the text editor or other application at

which you wish to enter the text.

Set the input mode to half-byte

characters.

Data cannot be output automatically to the

GP-IB interface.

Output the data.
Press the

[TRIG]

key or input the EXT I/O

TRIG signal.

Measurement will start with trigger input,

and after measurement is complete, the

measured value will be output.
If the instrument is in the

STOP

state or

the trigger source is set to

EXTERNAL

the number of output data points will be

the same as the measurement count

setting (1 sample per trigger to 5000

samples per trigger).

See “Trigger measurement (measurement

with user-specified timing)” (p. 38).

www.

.com

[email protected]

1.800.561.8187

Содержание DM7275 Series
















































































































































































































Результаты поиска

Содержание DM7275 Series

Отзывы:

Бренды по названию

Популярные бренды

Hioki DM7275 Series, Инструкция по эксплуатации

Результаты поиска

Содержание DM7275 Series

Отзывы:

Бренды по названию

Популярные бренды