Hioki DM7275 Series Скачать руководство пользователя страница 170

Страница: 170 / 207

171

Q&A (Frequently Asked Questions)

No.

Issue

Items to check

Possible causes → Solutions

See

2-6

Measured

temperature is not

displayed correctly.

Temperature sensor

There is a problem with the

connection.

→ Connect the temperature sensor

by inserting the plug all the way in.

The specified temperature sensor

has not been used.

→ Use the Z2001 Temperature

Sensor.

p. 27

The temperature sensor is

defective.

→ Replace the Z2001 Temperature

Sensor.

Sub-display

Trend and settings

screens

Temperature cannot be displayed

on the trend display or settings

screens.

→ Close the trend display or

settings screen.

p. 16

2-6

Measured

temperature is not

displayed correctly.

STOP

EXTERNAL

trigger

Temperature is updated based on

the voltage. Temperature will not

be updated when measurement is

stopped.

→ Push

[TRIG]

key to execute

triggered measurements or restart

continuous measurements.

p. 37

p. 38

3. Communications

Operation can be easily confirmed by referring to “8.3 Communications Settings” (p. 109).

No.

Issue

Items to check

Possible causes → Solutions

See

3-1

The instrument is

not responding at

all.

Display

REMOTE

icon is not

displayed

Connection is not established.

→ Check whether the connector

has been connected.

→ Check whether the interface

setting is correct.

(USB)→ Install the driver in the

control device.

p. 98

(RS-232C)→ Use a cross cable.

p. 101

(USB, RS-232C)→ Check the COM

port number on the control device.

p. 98

p. 100

(RS-232C)→ Use the same

communication speed for the

instrument and the control device.

p. 100

REMOTE

icon is

displayed

Commands are not accepted.

→ Check the software delimiter.

→ (GP-IB) Check the message

terminator setting.

→ (GP-IB) Check whether

the address setting has been

configured properly.

p. 102

Maintenance and Service

www.

.com

[email protected]

1.800.561.8187

Содержание DM7275 Series
















































































































































































































Результаты поиска

Содержание DM7275 Series

Отзывы:

Бренды по названию

Популярные бренды

Hioki DM7275 Series, Инструкция по эксплуатации

Результаты поиска

Содержание DM7275 Series

Отзывы:

Бренды по названию

Популярные бренды