manualshive.com logo in svg

Hioki DM7275 Series, Инструкция по эксплуатации

Поделиться
Скачать
Hioki DM7275 Series Скачать руководство пользователя страница 14

8

Operating Precautions

Installation method

 CAUTION

Do not place the instrument on an unstable table or an inclined place. Dropping or 

knocking down the instrument can cause injury or damage to the instrument.

 • Install the instrument with the bottom facing down.

 • To prevent overheating, be sure to leave the specified clearances around the instrument.

50 mm or more

50 mm or more

150 mm or more

Rear

The stand can be used to lift the instrument's front panel. (p. 14)

The instrument can also be mounted on racks.

（

p. Appx.14

）

Unplugging the power cord kills power to the instrument. Be sure to provide enough unobstructed 

space to unplug the power cord immediately in an emergency.

Handling the instrument

 DANGER

To avoid electric shock, do not remove the instrument's case. The internal 

components of the instrument carry high voltages and may become very hot 

during operation.

 CAUTION

To avoid damage to the instrument, protect it from physical shock when transporting 

and handling. Be especially careful to avoid physical shock from dropping.

This instrument may cause interference if used in residential areas. Such use must be avoided 

unless the user takes special measures to reduce electromagnetic emissions to prevent 

interference to the reception of radio and television broadcasts.

Precautions when using the included application disc

 • Exercise care to keep the recorded side of discs free of dirt and scratches. When writing text on a 

disc’s label, use a pen or marker with a soft tip.

 • Keep discs inside a protective case and do not expose to direct sunlight, high temperature, or 

high humidity.

 • Hioki is not liable for any issues your computer system experiences in the course of using this 

disc.

Before connecting a power cord

 WARNING

To avoid electrical accidents and to maintain the safety specifications of this 

instrument, connect the power cord provided only to an outlet.

www.

.com

[email protected]

1.800.561.8187

Содержание DM7275 Series
















































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды