Hioki DM7275 Series Скачать руководство пользователя страница 103

Страница: 103 / 207

101

Preparing to Use an Interface (Connection and Settings)

(3) Connect the RS-232C cable.

Before connecting the RS-232C cable, read “Before connecting the communication cables” (p. 10)

and “Before connecting to the RS-232C or GP-IB connectors” (p. 11) carefully.

Connect the RS-232C cable to the RS-232C connector. When connecting the cable, be sure to

tighten the fastening screws.

RS-232C cable

Computer’s

RS-232C interface

1 2 3 4 5

6 7 8 9

D-sub 9-pin male with

fastening screw #4-40

•When connecting the instrument to an external

device (DTE), use a crossover cable that satisfies

the specifications of the instrument’s connector

as well as the external device’s connector.

•The I/O connector implements terminal (DTE)

specifications.

•The instrument uses pin numbers 2, 3, and 5.

Other pins are unused.

Pin no.

Signal name

Signal

Remarks

Common

name

EIA

JIS

DCD

Data carrier detect

Not connected

RxD

Receive data

TxD

Transmit data

DTR

Data terminal ready

Fixed ON level (+5 to +9 V)

GND

Signal ground

DSR

Data set ready

Not connected

RTS

Send request

Fixed ON level (+5 to +9 V)

CTS

Clear to send

Not connected

Ring indicator

Not connected

When connecting the instrument to a computer

Use a D-sub 9-pin male to D-sub 9-pin male crossover cable.

D-sub 9-pin male

Instrument

D-sub 9-pin male

Computer (AT-compatible)

Pin no.

DCD

RxD

TxD

DTR

GND

DSR

RTS

CTS

Recommended cable: Hioki 9637 RS-232C Cable (1.8 m)

Preparing

to Use USB, RS-232C,

GP-IB,

and LAN

Control

www.

.com

[email protected]

1.800.561.8187

Содержание DM7275 Series
















































































































































































































Результаты поиска

Содержание DM7275 Series

Отзывы:

Бренды по названию

Популярные бренды

Hioki DM7275 Series, Инструкция по эксплуатации

Результаты поиска

Содержание DM7275 Series

Отзывы:

Бренды по названию

Популярные бренды