Hioki DM7275 Series Скачать руководство пользователя страница 141

Страница: 141 / 207

140

Timing Chart

(1) When the trigger source is set to

EXTERNAL

and EOM output is set to

HOLD

Inputting the TRIG signal will cause the EOM signal to turn off and measurement to start. When

measurement completes, the EOM signal will turn on and remain on until the next TRIG signal is

input.

See “11 EOM signal output type” (p. 137).

TRIG

EOM

OFF

HI, IN, LO, ERR

OB, BIN0 – BIN9

ON/OFF

OFF

Contact

check

Measurement
processing

Delay

Measurement Calculation

•The TRIG signal is ignored while the EOM signal is off (i.e., while measurement is in progress).

•After changing settings, for example to switch ranges, allow processing time (100 ms) to elapse

before inputting the TRIG signal.

•The instrument will output the EOM signal as soon as the judgment result (HI, IN, LO, ERR, or

BIN) has been finalized. If the connected external device’s input circuitry is characterized by a

slow response, it may take time for the judgment result to be captured after the EOM signal is

detected as having turned on.

See “11 Measurement process (starting measurement from an external device and loading

judgment results)” (p. 142).

(2) When the trigger source is set to

EXTERNAL

and EOM output is set to

PULSE

The EOM signal will turn on when measurement completes. Once the EOM output pulse width (T9)

has elapsed, the EOM signal will return to the off state. Inputting the TRIG signal while the EOM

signal is on will cause the EOM signal to turn off and measurement to start.

See “EOM signal output type” (p. 137).

TRIG

EOM

OFF

HI, IN, LO, ERR

OB, BIN0 – BIN9

OFF

ON/OFF

Contact

check

Measurement
processing

Delay

Measurement Calculation

www.

.com

[email protected]

1.800.561.8187

Содержание DM7275 Series
















































































































































































































Результаты поиска

Содержание DM7275 Series

Отзывы:

Бренды по названию

Популярные бренды

Hioki DM7275 Series, Инструкция по эксплуатации

Результаты поиска

Содержание DM7275 Series

Отзывы:

Бренды по названию

Популярные бренды