manualshive.com logo in svg

GSi JK125P, Руководство пользователя

Поделиться
Скачать
GSi JK125P Скачать руководство пользователя страница 94

GSI Group - Laser Division 
JK300HP/JK300P/JK125P 
Pre-installation and User Manual 

Issue 2.0

 

Page 80 of 172 

Part No: 1EA300E01

 

7.4.14 Alarm 2n14 : Interlock Chain Input 14 Fault 

Meaning: 

For JK laser products this input is allocated to the control rack dual shutter card slot 1 
Emergency Stop circuit.  Channel 1 of the dual shutter card. 

Possible causes: 

1. 

Interlock override not fitted to the control rack dual shutter card slot 1 (required if 
there is no dual shutter card fitted in slot 1). 

2. 

Dual shutter card not fitted in slot 1 of the control rack. 

3. 

Shutter card override connections not present (required if there is no shutter fitted to 
the dual shutter card channel 1). 

4. 

Shutter fault on the shutter fitted to channel 1 of the dual shutter card in slot 1 of the 
control rack. 

5. 

Dual shutter card fitted in slot 1 of the control rack is not programmed. 

6. 

Laser Control Card not fitted. 

7. 

Laser Control Card not programmed. 

8. 

Faulty shutter connected to channel 1 of the dual shutter card fitted in slot 1 of the 
control rack. 

9. 

Faulty shutter card fitted in slot 1 of the control rack. 

There is no voltage supply to this interlock input. 

Possible causes:  

1. 

Interlock supply not turned on. 

2. Loose 

connection. 

3. 

Faulty interlock module.  

7.4.15 Alarm 2n15 : Interlock Chain Input 15 Fault 

Meaning: 

For JK laser products this input is allocated to the control rack dual shutter card slot 2 
Emergency Stop circuit.  Channel 1 of the dual shutter card. 

Possible causes: 

1. 

Interlock override not fitted to the control rack dual shutter card slot 2 (required if 
there is no dual shutter card fitted in slot 2). 

2. 

Dual shutter card not fitted in slot 2 of the control rack. 

3. 

Shutter card override connections not present (required if there is no shutter fitted to 
the dual shutter card channel 1). 

4. 

Shutter fault on the shutter fitted to channel 1 of the dual shutter card in slot 2 of the 
control rack. 

5. 

Dual shutter card fitted in slot 2 of the control rack is not programmed. 

6. 

Laser Control Card not fitted. 

7. 

Laser Control Card not programmed. 

8. 

Faulty shutter connected to channel 1 of the dual shutter card fitted in slot 2 of the 
control rack. 

9. 

Faulty shutter card fitted in slot 2 of the control rack. 

There is no voltage supply to this interlock input. 

Petitioners Canadian Solar Inc. and Canadian Solar (USA) Inc. 

Ex. 1025, p. 80

Содержание JK125P



























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды