GSi JK125P Скачать руководство пользователя страница 133

Страница: 133 / 186

GSI Group - Laser Division

JK300HP/JK300P/JK125P

Issue 2.0

Pre-installation and User Manual

Part No: 1EA300E01

Page

119 of 172

Refer to Figure 17 for item identification.

Step

Action

WARNING
ELECTRIC SHOCK HAZARDS EXIST.
ELECTRIC SHOCK CAN CAUSE SERIOUS OR FATAL INJURY.

Carry out Power OFF Sequence.
Wait for 2 minutes. This ensures that the capacitors have discharged to a safe
level.

ISOLATE AND LOCK OUT THE MAINS SUPPLY TO THE LASER.

Unlock and open the front door.

Refer to Section 9.4.2 and drain the Coolant.

Loosen the hoseclips on the Coolant Pump inlet and outlet pipes (items 5 and 9).

Pull the inlet and outlet pipes (items 5 and 9) away from the Coolant Pump
(item 6) connectors.

Using a spanner, remove the pump outlet adaptor.

Remove all 4 Bolts from the top of the electrical panel cover (item 8) located at the
top of the Pump

Remove the three screws located in the base of the Electrical Panel (item 8).

Remove and retain the Electrical Panel (item 8) from the top of the Coolant Pump
(item 6).

Note

Do Not Remove Three Phase Terminals, or any Plugs inside of the

Electrical Panel (Item 8)

Remove and retain the four nuts and bolts (item 7) securing the Coolant Pump to
the cabinet base. The bolts are accessible from underneath the cabinet.

CAUTION

The Coolant Pump is heavy. Care must be taken when lifting the Coolant
Pump Assembly.

Remove the Coolant Pump (item 6).

Petitioners Canadian Solar Inc. and Canadian Solar (USA) Inc.

Ex. 1025, p. 119

Содержание JK125P



























































































































































































Результаты поиска

Содержание JK125P

Отзывы:

Бренды по названию

Популярные бренды

GSi JK125P, Руководство пользователя

Результаты поиска

Содержание JK125P

Отзывы:

Бренды по названию

Популярные бренды