manualshive.com logo in svg

GSi JK125P, Руководство пользователя

Поделиться
Скачать
GSi JK125P Скачать руководство пользователя страница 104

GSI Group - Laser Division 
JK300HP/JK300P/JK125P 
Pre-installation and User Manual 

Issue 2.0

 

Page 90 of 172 

Part No: 1EA300E01

 

7.6.5  Alarm 4n05 : Power Supply Over Temperature  

Meaning:  

The power supply temperature switch has been activated. 

Possible causes: 

1. 

Configurable high temperature alarm level set too high. 

2. 

Incorrect cooler valve setting. 

3. 

Cooler valve stuck in the closed position. 

4. 

Factory supply cooling water turned off. 

5. 

Insufficient flow from factory cooling water supply. 

6. 

Faulty power supply. 

7.6.6  Alarm 4n06 : Power Supply Contactor In Fault 

Meaning:  

The power supply contactor is in when it should be out.  The power supply should be off. 

Possible causes:  

1. 

Faulty power supply. 

7.6.7  Alarm 4n07 : Power Supply Failed to initialise 

Meaning:  

The Interlock Module timed out waiting for power supply n to response to an initialisation 
command, and report that it had entered the initialised state during the laser start up 
sequence. 

Possible causes:  

1. 

Incorrect laser type setting. 

2. 

Loose laser control network connections. 

3. 

Faulty power supply. 

4. 

Faulty Interlock module. 

5. 

Faulty Laser Control Card. 

7.6.8  Alarm 4n08 : Power Supply Contactor In Timeout 

Meaning:  

The power supply contactor did not engage within the timeout period during the laser start 
up sequence. 

Possible causes: 

1. 

Faulty power supply. 

7.6.9  Alarm 4n09 :  Power Supply Failed To Simmer 

Meaning:  

The Interlock Module timed out waiting for power supply n to enter, and report that it had 
entered the simmer state during the laser start up sequence. 

Possible causes:  

1. 

Incorrect laser type setting. 

Petitioners Canadian Solar Inc. and Canadian Solar (USA) Inc. 

Ex. 1025, p. 90

Содержание JK125P



























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды