GSi JK125P Скачать руководство пользователя страница 7

Страница: 7 / 186

GSI Group - Laser Division

JK300HP/JK300P/JK125P

Issue 2.0

Pre-installation and User Manual

Part No: 1EA300E01

Page vii

Table of Contents

General Information...................................................................................................... 3

1.1

Class of Laser ..................................................................................................... 3

1.2

Intended Users.................................................................................................... 3

1.3

Documentation .................................................................................................... 3

1.3.1

Safety Paragraphs ................................................................................ 3

1.4

Table of Definitions ............................................................................................. 4

1.5

After Sales Support ............................................................................................. 7

1.6

CE Mark Information ........................................................................................... 7

1.7

The JK300HP/JK300P/JK125P Series Laser ..................................................... 8

1.7.1

Main Assemblies ................................................................................... 8

1.7.2

Control System and Local Controller .................................................... 9

1.7.3

Machine Interface.................................................................................. 9

1.7.4

Ancillaries.............................................................................................. 9

1.8

Technical Specification ..................................................................................... 10

1.9

Safety Interlocks................................................................................................ 14

1.9.1

Customer Remote Interlocks............................................................... 14

1.9.2

Shutter Interlocks (Beampath Interlocks) ............................................ 14

1.10

Laser Power Delivery ........................................................................................ 15

1.11

Operating Parameters....................................................................................... 17

1.11.1

Changing Parameters ......................................................................... 17

1.11.2

Parameter Set Selection ..................................................................... 19

1.12

Laser Outputs.................................................................................................... 19

1.13

Operating Guidelines ........................................................................................ 19

1.14

Processing Considerations ............................................................................... 19

1.15

Fibre Optic Handling ......................................................................................... 20

1.15.1

Description .......................................................................................... 20

1.15.2

Unpacking Fibre Optic Cable .............................................................. 20

1.15.3

Fibre Installation.................................................................................. 21

1.15.4

Minimum Bend Radii ........................................................................... 21

1.15.5

Fibre Optic Termination....................................................................... 22

1.15.6

Fibre Routing....................................................................................... 22

1.15.7

Fibre Removal..................................................................................... 22

Safety........................................................................................................................... 23

2.1

Laser Classification ........................................................................................... 23

2.2

Laser Radiation Hazards................................................................................... 25

2.3

Control Measures.............................................................................................. 25

2.4

Electrical Safety ................................................................................................ 27

2.5

Environmental Hazards..................................................................................... 28

2.5.1

Fire ...................................................................................................... 28

2.5.2

Fume ................................................................................................... 29

2.5.3

Compressed Gases ............................................................................ 30

2.5.4

Solvents .............................................................................................. 30

2.6

Conditions of Use.............................................................................................. 31

2.6.1

Approved Materials ............................................................................. 31

2.6.2

Approved Process............................................................................... 31

2.6.3

Approved Conditions........................................................................... 31

2.6.4

Due Authorisation................................................................................ 32

2.7

Safety Control System ...................................................................................... 33

2.7.1

Safety Category .................................................................................. 33

Petitioners Canadian Solar Inc. and Canadian Solar (USA) Inc.

Ex. 1025, p.

vii

Содержание JK125P



























































































































































































Результаты поиска

Содержание JK125P

Отзывы:

Бренды по названию

Популярные бренды

GSi JK125P, Руководство пользователя

Результаты поиска

Содержание JK125P

Отзывы:

Бренды по названию

Популярные бренды